Ground-breaking farm implements for sustainable profits

Anhydrous Ammonia NH3 

DF-1PM

DF-1PM/3/4DA

K-2T

K-2T/3/4/DA

DF-1PM

Designed with a parabolic front-swept shape for light tillage


Knife shanks are heat treated 5160 chromium manganese spring steel for toughness, durability and long wear life. They are welded on robotic welders to ensure accuracy and consistency.


Equipped with a durable 1 ¾” wide chrome carbide tip and shin to extend the wear life while allowing it to pull easy.


Unique chrome carbide foot piece creates a pocket under the soil to self-seal. This pocket gives the anhydrous a place to sit to allow it to go through its phase change to become available to the plants.


All chrome carbide wear surfaces and tube protectors are 26% chrome carbide with special alloys to extend the wear life.


½” knife and chrome carbide shin and rear section protect the tubes from wear.

DF-1PM/3/4DA

Same as DF-1PM but includes the rear 3/4” vapor tube to dispose of vapor. We recommend 2 vapor tubes for up to 17 row bar. For bars larger than 17 rows we recommend 4 vapor tubes.


Designed with a parabolic front-swept shape for light tillage


Knife shanks are heat treated 5160 chromium manganese spring steel for toughness, durability and long wear life. They are welded on robotic welders to ensure accuracy and consistency.


Equipped with a durable 1 ¾” wide chrome carbide tip and shin to extend the wear life while allowing it to pull easy.


Unique chrome carbide foot piece creates a pocket under the soil to self-seal. This pocket gives the anhydrous a place to sit to allow it to go through its phase change to become available to the plants.


All chrome carbide wear surfaces and tube protectors are 26% chrome carbide with special alloys to extend the wear life.


½” knife and chrome carbide shin and rear section protect the tubes from wear.

K-2T


This conventional knife is a workhorse for standard ammonia application. It is ½” wide and features a narrow ¾” chrome carbide tip and foot to extend the life while still pulling easy.


Knife and chrome carbide tip are more upright to slice the soil while reducing lift.


½” knife and chrome carbide shin and rear section protect the tubes from wear.


All chrome carbide wear surfaces and tube protectors are 26% chrome carbide with special alloys to extend the wear life.

K-2T/3/4/DA


Same as K-2T but includes the ¾”rear vapor tube to dispose of vapor. We recommend 2 vapor tubes for up to 17 row bar. For bars larger than 17 rows we recommend 4 vapor tubes.


This conventional knife is a workhorse for standard ammonia application. It is ½” wide and features a narrow ¾” chrome carbide tip and foot to extend the life while still pulling easy.


Knife and chrome carbide tip are more upright to slice the soil while reducing lift.


½” knife and chrome carbide shin and rear section protect the tubes from wear.


All chrome carbide wear surfaces and tube protectors are 26% chrome carbide with special alloys to extend the wear life.

K-4TSDF

Anhydrous Ammonia (Minimal Disturbance)

 

Parabolic front-swept shape with a 1-1/4” wide foot for underground soil mixing without heavy surface disturbance. 

 

Knife shank is heat-treated 5160 chromium-manganese steel and is 3/8” thick with a rounded edge for minimum soil movement at the surface.   Point and tube protector are 26% chrome carbide for long wear life.


Available with crimped and drilled  3/8” tube for NH3 (K-4TSDF) or with open-end 3/8” tube for liquid (K-4TSDF/O).


Knife with added ¾” vapor tube is K-4TSDF/3/4DA.

DF-1PM/112

Parabolic front-swept shape with a 1-3/4” wide foot for light underground tillage and mixing dry fertilizer


Knife shank is heat-treated 5160
chromium-manganese steel and is 1/2” thick. 


Point is 26% chrome carbide for long wear life.   
1-1/2” dry tube is wear-protected with AR400 side plates, and a spreader plate is at the soil end to assist in distributing fertilizer evenly without blowing out at the surface.

 
Knife is designed to also accept extra liquid or ammonia tubes added in the field.

Anhydrous Ammonia & Dry Fertilizer

DF-1PM/112DA/3/4

K-2T/112DA

DF-1PM/112DA/3/4

This parabolic shaped knife is designed specifically for dual dry fertilizer and NH3
placement. The front-swept curvature is for light tillage. The fertilizer tube opens towards a plate to spread the outcoming fertilizer evenly in the furrow.


Knife shanks are heat treated 5160 chromium manganese spring steel for toughness, durability and long wear life. They are welded on robotic welders to ensure accuracy and consistency. 


Equipped with a durable 1 ¾” wide chrome carbide tip and shin to extend the wear life while allowing it to pull easy. 


Unique chrome carbide foot piece creates a pocket under the soil. This pocket gives the anhydrous a place to sit to allow it to go through its two-week phase change to become available to the plants. 


All chrome carbide wear surfaces and tube protectors are 26% chrome carbide with special alloys to extend the wear life.  


½” knife and chrome carbide shin and rear section protect the tubes from wear.

K-2T/112DA

This conventional knife was designed to apply dry fertilizer and NH3 in conventional ground. The dry fertilizer is protected behind a chrome carbide shield. It blows the fertilizer against a plate to spread it evenly across the furrow.


This knife is ½” wide and features a narrow ¾” chrome carbide tip and foot to extend the life while still pulling easy.


Knife and chrome carbide tip are more upright to slice the soil while reducing lift.


All chrome carbide wear surfaces and tube protectors are 26% chrome carbide with special alloys to extend the wear life.


We recommend 2 vapor tubes for 17 row bars and less and 4 vapor tubes for 18 rows and larger.  The part number for this knife with vapor tube is K-2T/112DA/3/4.

Liquid Fertilizer

DF-1PM/O

K-2T/O

DF-1PM/O

Designed with a parabolic front-swept shape for light tillage and 3/8” open end tube for liquid application.


Knife shanks are heat treated 5160 chromium manganese spring steel for toughness, durability and long wear life. They are welded on robotic welders to ensure accuracy and consistency.


Equipped with a durable 1 ¾” wide chrome carbide tip and shin to extend the wear life while allowing it to pull easy.


All chrome carbide wear surfaces and tube protectors are 26% chrome carbide with special alloys to extend the wear life.


½” knife and chrome carbide shin and rear section protect the tubes from wear.



K-2T/O

This conventional knife with open end tube is a workhorse for standard liquid application. It is ½” wide and features a narrow ¾” chrome carbide tip and foot to extend the life while still pulling easy.

 

Knife and chrome carbide tip are more upright to slice the soil while reducing lift.

 

½” knife and chrome carbide shin and rear section protect the tubes from wear.

 

All chrome carbide wear surfaces and tube protectors are 26% chrome carbide with special alloys to extend the wear life.

K-4TSDF/O

(Minimal Disturbance)

 

Parabolic front-swept shape with a 1-1/4” wide foot for underground soil mixing without heavy surface disturbance. 

 

Knife shank is heat-treated 5160 chromium-manganese steel and is 3/8” thick with a rounded edge for minimum soil movement at the surface.   Point and tube protector are 26% chrome carbide for long wear life.


Available with crimped and drilled  3/8” tube for NH3 (K-4TSDF) or with open-end 3/8” tube for liquid (K-4TSDF/O).


Knife with added ¾” vapor tube is K-4TSDF/3/4DA.

Anhydrous Ammonia & Liquid Fertilizer

K-2TA/DA

K-2T/DA

This conventional knife is a dual product liquid and NH3 version of the workhorse K-2T. It is ½” wide and features a narrow ¾” chrome carbide tip and foot to extend the life while still pulling easy.


Knife and chrome carbide tip are more upright to slice the soil while reducing lift.


½” knife and chrome carbide shin and rear section protect the tubes from wear.


All chrome carbide wear surfaces and tube protectors are 26% chrome carbide with special alloys to extend the wear life.


For liquid fertilizer and NH3, we recommend 2 vapor tubes for a 17-row bar or smaller, and 4 vapor tubes for bars 18 rows or larger. The identical knife part number with vapor tube is K-2T/DA/3/4.